Mouth Guard Size Guide: Adult, Youth and Kid Arches

Arch size, not age, decides whether a mouth guard stays in place. We hold 260+ moulds across adult, youth and kid arches, so you can size a range without paying for new tooling. This guide gives the arch widths, lengths and shell thicknesses we mould, the 2 mm trimming rule our QC team applies, and the fit check a buyer can run on a sample before placing 100 pcs.

Arch dimensions

Sizing starts with the arch, not the age on the box

Our adult arch block measures 58 to 62 mm across the second molar and 68 to 72 mm from the labial face to the last molar. Youth arches run 50 to 54 mm wide and 60 to 64 mm long, and kid arches 46 to 50 mm by 54 to 58 mm. We measure these on a cast, not from a photo.

Shell thickness follows the sport, not the arch. Kids guards sit at 2.0 mm, youth at 2.5 mm, adult single layer at 3.0 mm and adult double layer at 3 + 2 mm. A guard that is 0.5 mm too thick will not seat on the molars during a bite, and one that is 0.5 mm under spec rocks when the jaw closes.

  • Adult arch: 58–62 mm wide, 68–72 mm long
  • Youth arch: 50–54 mm wide, 60–64 mm long
  • Trimming: 2 mm maximum per pass, 2 mm kept behind the last molar
Ask for a size sample set
Adult and youth mouth guard arches measured with a calliper
Sizing decisions

Where a size range goes wrong

Most fit complaints come from three places, and all three are settled before production starts.

Reading an arch width

Measure across the second molar, not the front teeth. A 4 mm error moves a guard from a youth block to an adult block.

Trimming in the wrong place

Take material from the rear and the labial edge, never from the bite face. Two 2 mm passes fit better than one 4 mm cut.

Braces and mixed dentition

A guard over braces needs 1 mm of relief and a 2.5 mm shell, because brackets push the plastic away from the molars.

Fit testing

A two-minute fit check you can run on a sample

Warm the guard in 70 °C water for 60 to 90 seconds, seat it on the upper arch and ask the wearer to bite, swallow and open wide. The guard should hold without finger pressure and lift no more than 1 mm at the back when the jaw opens. Anything looser will be dropped in play, and a dropped guard is a return.

We hold ±0.5 mm on arch width across a run of 2,000 pcs, because a retailer mixing two sizes in one shelf box will hear about it from customers. Each carton is labelled with the mould number, the 3.0 mm shell thickness and the arch block it came from, so a complaint can be traced back to one press cycle and one operator.

  • Retention check: no more than 1 mm of lift at the rear
  • Arch width held to ±0.5 mm across the run
  • Carton labelled with mould number, thickness and arch block
Assembler checking the fit of a youth mouth guard on a plaster cast
Sizing for retail

How to build a size range that sells through

A shelf box with three sizes sells better than one size in three colours, because the customer is buying fit. We suggest one adult block at 3.0 mm, one youth block at 2.5 mm and one kid block at 2.0 mm, with the arch width printed in millimetres on the sleeve. Buyers who print a size chart on the back of the pack report fewer size-related messages than those who print age ranges alone.

Sampling a size range costs the same as sampling a single size, because we cut from moulds already on file. Send us an impression, a scan file or a used guard, and we will match it to the nearest block and tell you where the 1 mm gaps sit. If no block is close, a new cavity is quoted separately and belongs to you.

  • One block per age band, arch width printed on the sleeve
  • Impression, scan file or used sample accepted for matching
  • New cavity quoted separately and owned by the buyer
Measurements

Adult, youth and kid arch measurements

Internal mould dimensions, measured on a plaster cast. Add 0.3 mm to 0.5 mm for a guard that will be worn over braces.

Adult arch width
58–62 mm across the second molar
Adult arch length
68–72 mm from labial face to last molar
Adult shell thickness
3.0 mm single layer, 3 + 2 mm double layer
Youth arch width
50–54 mm across the second molar
Youth arch length
60–64 mm from labial face to last molar
Youth shell thickness
2.5 mm single layer
Kid arch width
46–50 mm, ages 6 to 11
Kid shell thickness
2.0 mm single layer
Trimming rule
Remove 2 mm maximum per pass from the rear or labial edge, keep 2 mm of shell behind the last molar, and re-fit after each pass in 70 °C water
Fit check
The guard must not rock more than 1 mm at the rear when the jaw opens, and must lift off without finger pressure
Sizes

Adult, youth and kid blocks

Process

How a size range gets approved

01

Send the arch data

An impression, a scan file or a used guard tells us more than an age range on a brief.

02

Block matching

We match your measurement to one of 260+ moulds and report the gap in millimetres.

03

Sample set

Three sizes ship in 5 to 7 days, each labelled with its arch width.

04

Wear trial

Two wearers per size test retention for 30 minutes of light contact work.

05

Bulk and packing

Production runs 12 to 18 days, 300 pcs per carton, sizes labelled on the sleeve.

Indicative FOB

Size runs at three volumes

Per piece, unprinted, in a vented case. A size run costs the same per piece as a single size, because the moulds are already on file.

Two sizes

$0.95 / pc

100 pcs across adult and youth as two colourways of 50, 3.0 mm and 2.5 mm.

  • One colourway, two sizes per carton
  • Sampling 5–7 days, production 12–18 days
  • Fit check sheet included with the sample

Range programme

$0.52 / pc

2,000 pcs across the full arch range, size marks printed on the guard and stock held.

  • 260+ moulds, no new cavity for standard blocks
  • Price held for 6 months on repeat sizes
  • FOB Shenzhen or Yantian, CIF or DDP

Send an impression or a scan, get a size match in 6 hours

Tell us the ages you sell to and the sport. We reply with the closest block, the arch width in millimetres and a sampling date.

FAQ

Mouth Guard Size Guide: common questions

How do I know which size to stock for a school team?
Stock the youth block at 2.5 mm for ages 12 to 15 and the adult block at 3.0 mm for 16 and over. Ask the coach for the two widest and two narrowest arches, then measure those four on a cast.
Can you trim a guard to fit a smaller arch?
Trimming works at the rear and labial edge only, 2 mm per pass. It cannot narrow the bite face, so a guard more than 4 mm too wide should move down a block instead.
What is the difference between youth and kid sizing?
The youth block is 50 to 54 mm wide with a 2.5 mm shell, for ages 12 to 15. The kid block is 46 to 50 mm wide at 2.0 mm, for ages 6 to 11 and mixed dentition.
Do you supply a sizing chart for retail packaging?
Yes. We send a print-ready chart with arch widths in millimetres, shell thickness and a fit check drawing, at 300 dpi, sized to your sleeve or tuck box.
Can I order a sample set in three sizes?
Three sizes ship in 5 to 7 days, each labelled with its arch width and shell thickness. The set is charged as a sample and credited against your first bulk order.

Ready to cost your next mouth guard order?

Send your reference, quantity and target price. We reply with a quotation and a sampling date within 6 working hours.