Mouth Guard Materials: EVA, TPE and Transparent EVA

We mould mouth guards in three material families: food-grade EVA, TPE and transparent EVA, plus silicone gel liners and TPU tethers. Each grade softens at a different water temperature, sits at a different Shore hardness and lands at a different cost per piece. This page sets out the numbers you need to specify a guard that fits your sport, your retail price and your carton budget.

Material selection

Three grades, one compression moulding floor

Every guard we press starts as a sheet or a pellet. Food-grade EVA arrives as 3.0 mm and 4.0 mm sheet, TPE as 2.5 mm sheet, and transparent EVA as 2.0 mm sheet that needs a polished cavity. All three run on the same 260 moulds and the same 120 staff, so switching grade between orders does not reset your sampling clock.

Fitting temperature is the first thing your retail customer will notice. EVA softens at 70–75 °C in 60 to 90 seconds, TPE at 75–80 °C in 45 to 60 seconds, and transparent EVA needs the full 90 seconds because heat moves slowly through a clear sheet. A guard that will not soften in the time printed on the box comes back as a return.

  • 260+ moulds on file for adult, youth and kid arches
  • Fitting temperature logged per batch on the QC sheet
  • Mould ownership transferred to you on request
Request a material sample
EVA sheet being pressed in a mouth guard moulding press
What drives the choice

Three decisions decide the grade you need

Sport, fit route and comfort layer point to one grade before price is even discussed.

Contact level and thickness

Rugby, hockey and boxing use 3.0 mm to 4.0 mm EVA or a 3 + 2 mm double layer; basketball and youth guards sit at 2.0 mm to 2.5 mm.

Fit route: boil and bite or custom

Boil and bite suits retail packs; a thermoformed custom guard needs an impression and a 3D model, which adds 5 to 7 days to sampling.

Liner and tether

A silicone gel liner at Shore A 20 to 30 softens the bite face; a TPU tether holds 60 N in a static pull test before it releases.

Quality control

How each material batch is checked before it ships

Incoming sheet is checked for thickness at five points, and anything outside ±0.15 mm is rejected before cutting. We press a trial guard from each new batch, fit it in a 70 °C water bath and time the softening window, then record the result against the batch number. Bulk inspection runs to AQL 2.5 on a 300-piece carton, at 30 g per guard.

Transparent EVA shows every flow line, so those cavities are polished to a 0.4 µm finish and inspected under a 500 lux lamp before the first shot. EVA and TPE hide small marks but not wall drift. We section one guard per 500 and measure the bite face with a calliper, and anything under 2.8 mm against a 3.0 mm spec goes to scrap.

  • Thickness tolerance ±0.15 mm on every incoming sheet
  • Batch samples retained for 12 months against the batch number
  • AQL 2.5 inspection before the carton is sealed
Calliper measuring the wall thickness of a moulded mouth guard
Compliance and tooling

What a factory can and cannot document

Food-contact paperwork is where most material questions end up. We hold REACH SVHC declarations, phthalate-free statements and migration test reports for each grade, and we issue a batch declaration of conformity with your order. What we cannot do is print a CE mark on a mouth guard: no harmonised standard covers it, so any CE logo on a retail box is a claim your importer owns, not the moulding floor.

Tooling is the other half of the material decision. We keep 260+ moulds on file, which covers most adult, youth and kid arches without a new cavity. A new geometry needs a machined aluminium cavity, and that tool belongs to you once you have paid for it, with drawings handed over on request. A colour change in EVA or TPE adds 5 to 7 days to sampling because the press needs a clean run between shades.

  • REACH SVHC and phthalate-free declarations per grade
  • Migration test reports for food-contact grades
  • Batch declaration of conformity issued with each order
  • New cavity tooling owned by you, drawings on request
Material comparison

EVA, TPE and transparent EVA side by side

Indicative FOB per piece at 500 pcs, 3.0 mm single layer in a vented case. Sheet prices move with oil-linked monomer, so treat these as a planning figure.

EVA: fitting temperature
70–75 °C water, 60 to 90 seconds, then 30 seconds to cool
EVA: hardness
Shore A 60 to 70
EVA: cost per piece
about $0.68 at 500 pcs
EVA: typical use
Rugby, hockey, boxing, school team orders at 3.0 mm to 4.0 mm
EVA: carton note
300 pcs per carton at 30 g per guard, 12.6 kg gross with cases
TPE: fitting temperature
75–80 °C water, 45 to 60 seconds
TPE: hardness
Shore A 50 to 60
TPE: cost per piece
about $0.78 at 500 pcs, roughly 15 percent above EVA
TPE: typical use
Youth and retail packs where a softer bite face sells the product
TPE: carton note
300 pcs per carton at 30 g per guard, same 560 × 420 × 380 mm box
Transparent EVA: fitting temperature
75–80 °C water, 90 to 120 seconds
Transparent EVA: hardness
Shore A 70 to 75
Transparent EVA: cost per piece
about $0.88 at 500 pcs, roughly 30 percent above EVA
Transparent EVA: typical use
Clear guards for sports where the wearer wants the teeth visible
Transparent EVA: carton note
300 pcs per carton, each guard in a tissue sleeve to stop scuffing in transit
Materials in production

What the grades look like on the floor

Process

From material brief to bulk in five steps

01

Material brief

You send the sport, contact level and target retail price; we shortlist two grades within 6 working hours.

02

Sample set

You receive three guards in the shortlisted grades, 5 to 7 days after the drawing is approved.

03

Fit trial

You test the softening window in your own water bath and confirm the Shore hardness you need.

04

Bulk run

Production takes 12 to 18 days after sample approval, with a thickness check every 300 pieces.

05

Inspection and ship

AQL 2.5 inspection, 300 pcs per carton, FOB Shenzhen or Yantian, CIF or DDP on request.

Indicative FOB

What the same 3.0 mm EVA guard costs at three volumes

Prices are per piece, unprinted, in a vented case. Setup, plates and press time are fixed costs, so the per-piece figure falls as the run grows.

Trial order

$0.95 / pc

100 pcs in two colourways of 50, 3.0 mm EVA, vented case and printed sleeve included.

  • Mixed sizes across adult and youth arches
  • Sampling 5–7 days, production 12–18 days
  • Carton of 300 pcs at 30 g per guard

Programme

$0.52 / pc

2,000 pcs with a 4.0 mm double-layer option, quarterly call-off and stock held for repeat sizes.

  • 260+ moulds on file, no new cavity at this volume
  • Price held for 6 months on repeat colourways
  • Reorder from 100 pcs after the first run

Send your material brief, get a sample plan in 6 hours

Tell us the sport, the quantity and the water temperature your retail box will print. We reply with two grades, a cost per piece and a sampling date.

FAQ

Mouth Guard Materials: common questions

Which mouth guard material should I choose for contact sport?
For rugby, hockey and boxing, 3.0 mm to 4.0 mm EVA gives the longest wear life at the lowest cost per piece. TPE suits youth and retail packs where a softer bite face sells the product.
Is transparent EVA more expensive than standard EVA?
Yes. Clear grade sheet costs more, the cavity needs a 0.4 µm polish, and flow lines show under 500 lux, so yield is lower. Expect roughly 30 percent more per piece at 500 pcs.
What water temperature should the retail box recommend?
Print 70–75 °C for EVA and 75–80 °C for TPE and transparent EVA, with 60 to 90 seconds of immersion. A household kettle and a timer cover both without special equipment.
Can you supply food-contact documentation for each grade?
We issue REACH SVHC declarations, phthalate-free statements and migration test reports per grade, plus a batch declaration of conformity. We do not put a CE mark on mouth guards, because no harmonised standard covers them.
Do we own the mould if we pay for a new cavity?
Yes. A new aluminium cavity is charged once, belongs to you, and the drawings transfer on request. We hold the tool at Dalingshan for your reorders, and you can move it after the final shipment.

Ready to cost your next mouth guard order?

Send your reference, quantity and target price. We reply with a quotation and a sampling date within 6 working hours.